Industrial products
EUROMIX RAPİT INDUSTRIAL PAINT
Fast drying ,glossy,elastic,wear resistant and easy to apply industrial paint.
PRODUCT GROUP | Solvent -borne alkyd gloss paint. |
APPLICATION AREAS | Agricultural tools and machinery, home and garden appliances, metallic accessories,furniture,pipes, valves,etc. |
PREPARATION | Remove,dirt,rust,oil and grease throughly from the application surface.Apply paint directly on bare metal or appropriately undercoat surface. |
COLOUR NUMBER | 16 standart production. |
COVERING CAPACITY | 12-13 M2/lt. dependent on the substrate. |
APPLICATION | Min. 2 coat. |
DRYING(25 C) | set to touch dry in 30-45 minutes set to handle in 24 hours hard dry in 3 hours. |
APPLICATION MEANS | Brush,spray. |
THINNER | Rapit Thinner. |
THINNING INFORMATION | % 15-20 |
PACKEGE INFORMATION | 1 LT.,2.75 LT ve 15 LT. |

EUROMIX INDUSTRIAL PRIMER
All kinds of protection against corrosion of iron surface provides high in protection is applied to the surface a good filling, creating high film surface protection, good adhesion of topcoat to make it appear smoother and a good features covering primer.
PRODUCT GROUP | Solvent-based primer |
APPLIED SURFACE VIEW | Dull, flat. |
APPLICATION AREAS | All kinds of metal surface. (agricultural tools, metal tools and devices) |
COLOUR NUMBER | Grey,white,red |
COVERING CAPACITY | 10-12 m2/lt single coat. (according to their surface completely vary.) |
APPLICATION | 1 coat |
DRYING(25 C) | Not hold dust :15-20 min. Touch dry :30-45 min. Through dry: approx 3 hours Drying assembly: approximately 24 h |
APPLICATION MEANS | Brush,spray. |
THINNER | Rapit Thinner. |
THINNING INFORMATION | % 15-20 |
PACKEGE INFORMATION | 15 LT. |

EUROMIX CELLULOSIC PAİNT
Nitrocellulose and alkyd based topcoat paint.
Furniture and metal industries
have been developed for. Is resistant to physical
blows.
A bright and quick-drying paint.
Product and Additives | Cellulose Topcoat Economic Super Cellulosic Thinner |
Raw materials | nitrocellulose combinations |
Surface Preparation | Wood substrates, CELLULOSIC PRIMER should be applied. Metal surfaces, SAC ASTAR applied and sanded on the CELLULOSIC should be applied to the surface. |
Application | Diagonally into 2 or 3 times the floor is applied. Solvent to evaporate for 5 minutes between floors should be expected. |
Used Tools | 1,5-1,8 mm diameter nozzle with pistol implementation is recommended. |
Thinning / Mixing Ratio | Be viewed at a rate of 35-45% with CELLULOSIC THINNER. |
Can be painted (container that can be) Area | approximately 8-10 m2/lt single floor. area is painted. floor. area is painted. |
Dry time: 20 º C | Touch dry in 10 minutes, hard dry complements 2-2.5 hours. |
Flash Point | <21 ° C |

EUROMIX CELLULOSIC PRİMER
Nitrocellulose and alkyd-based primer paint.
Furniture and metal industries have
been developed for. Good adhesion to the
surface. Has a high fill power.
Is easy and quick dry sanding.
Surface Preparation | Old and scratched after loose paints, surface P 180 should be sanding with emery, dirt, rust, and oil should be cleaned. Metal surfaces before applying primer, CELLULOSIC THINNER and better adhesion to be deleted with the SAC to be primed with PRIMER. |
Application | 2 or 3 times as apply. 5 minutes between coats should be expected. |
Tools used | Pistole |
Thinning / Mixing Ratio | CELLULOSIC THINNER at a rate of 35-40% and is. viewed with |
Can be painted (container that can be) Area | approximately 12 m2/kg additional floor. areas are primed. |
Drying Time | (20 ° C) 5-15 minutes to touch dry, hard dry in 2 hours completes. 3 hours after the application is made can be abrasive. |
Flash Point | <21 ° C |

EUROMIX EPOXY SOLVENT COAT
APPLICATION AREAS | A two-component epoxy resin based topcoat paint. Carrying properties of epoxy resin, water, chemicals and solvents resistant, high abrasion resistance paint. |
COLOUR | Optional |
Specifications | Density (g / ml) (20 ° C): 1.35 ± 0.05
Brightness: Bright, Semi-matte Flash Point (° C): 22 Heat Strength (Dry) (° C): 140 Covering Capacity (Theoretical): 5.5 - 11 m² / kg (25 to 50 µ dry film thickness) Mixing ratio (by weight): I. Component: 3.5 / II. Component: 1 (Hardener) Mixture Life (20 ° C): 8-12 hours. Film thickness recommended age: 70 to 110 µ Dry film thickness can be obtain in Single Layer: 30 - 50 µ |
Drying Time | First Movement: 1 - 2 hours to dry 5-6 hours
(20 ° C - Max. 85% relative humidity) recoat: 24 hours Full Hardening: 7 days. |
Thinning rate | Depending on the application form at a rate
of 5-10% by weight can be viewed with Epoxy
Paint Thinner.
Full Hardening: 7 days. |
Application 1 | Are applied to primed surface. Be applied must be clean and dry surfaces. |
Application 2 | I. and II. Attention to the mixing ratio of the components are mixed together, after resting for 5-10 minutes, brush, air or airless gun in one or two layers, layer is applied between the 24 hours be expected. |
Storage Conditions | Not receive direct sunlight 5-35 ° C increase in environments, can be stored for one year in unopened original packaging. Must be protected from excessive heat and humidity. |
Important Notices | Components must be mixed with each other During application ambient temperature must be between 5-35 ° C. After each application, application tools should be cleaned with Epoxy Paint Thinner. Discharging sewage and water channels should definitely paint. Application, as noted above and should be done in well-ventilated place |
Packaging | I. Component: 21kg / II. Component: 6.00 kg |

EUROMIX EPOXY SOLVENT PRIMER
Two-component epoxy resin based primer is Anticorrosive.
Resistant to chemicals,
non-toxic paint pigment containing primer
APPLICATION AREAS | Metal surfaces, corrosion protection purposes is used safely. |
COLOUR | white,grey |
Specifications | Density (g / ml) (20 ° C): 1.50 ± 0.05
Brightness: matt Flash Point (° C): 22 Heat Strength (Dry) (° C): 120 Covering Capacity (Theoretical): 5.5 m² / kg (25 to 50 μ dry film thickness) Mixing ratio (by weight): I. Component: 5.3 / II. Component: 1 (Hardener) Mixture Life (20 ° C): 8-12 hours. Film thickness recommended age: 65 to 110 μ Dry film thickness can be obtain in Single Layer: 30 - 50 μ |
Drying Time | Fırça ,rulo ,havalı ve havasız tabanca ile uygulanır. |
UYGULAMA SICAKLIĞI (20 ° C - Max. 85% relative humidity) |
First Drying: 30 minutes, Drying: 1-2 hours to recoat: 14-16 minutes Full Hardening: 7 days. |
Thinning rate | Depending on the application form at a rate of 5-10% by weight can be viewed with Epoxy Paint Thinner. |
Application 1 | Sa Sa 2 ½ 2 or preferably sand rasp. Be applied must be clean and dry surfaces. |
Application 2 | I. and II. Attention to the mixing ratio of the components are mixed together, after resting for 5-10 minutes, brush or airless gun in one or two times, times between 16 hours is expected to be applied. |
Storage Conditions | Not receive direct sunlight 5-35 ° C increase in environments, can be stored for one year in unopened original packaging. Must be protected from excessive heat and humidity. |
Important Notices | Components must be mixed with each other During application ambient temperature must be between 5-35 ° C. After each application, application tools should be cleaned with Epoxy Paint Thinner. Discharging sewage and water channels should definitely paint. Application, as noted above and should be done in well-ventilated place |
Packaging | I. Component: 24kg / II. Component: 4.50 kg |

EUROMIX SOLVENT FREE EPOXY TOPCOAT
Two-component solvent free epoxy resin based, self-spreading is a floor coating
Applied to concrete and metal surfaces that are not affected by chemical, physical
and chemical agent resistant, easy to clean, high mechanical strength is a floor
coating. According to the request may be smooth or rough surface coating.
2.5-3 mm thick is applied
APPLICATION AREAS | Warehouses of the factory, laboratory, etc.. sections, such as hospitals and markets business of the ground cover is used safely |
COLOUR | Optional |
Specifications | Density (g / ml) (20 ° C): 1.45 ± 0.10:
Brightness: Bright: Heat Strength (Dry) (° C): 140: Covering Capacity (Theoretical): 2.5-3 kg / m² (dry film thickness of 2.5-3 mm): Mixing ratio (by weight): I. Component: 3.8 / II. Component:1 (Hardener): Mixture Life (20 ° C) 1 hour (for 1 kg mixture): Dry film thickness can be obtain in Single Layer: 2.5 - 3 mm: |
Drying Time (20 ° C - Max. 85% relative humidity) |
First Movement: 1 - 2 hours Dry: 12 hours Full Hardening: 7 days |
Thinning rate | Addition of thinners is not recommended: |
Application 1 | Do not apply oil to the surface, must be free from dirt and moisture. Epoxy Concrete Sealer should be applied to surfaces Solvent and after waiting 24 hours drying coating should be applied. |
Application 2 | I. and II. Attention to the mixing ratio of the components are mixed together, after resting for 5-10 minutes; floor is spread with spatula or trowel. Roll coating over existing gear visit air bubbles are removed and properly spread out will be provided. To increase the mechanical resistance of the coating material to the mixture prepared at a rate of 30-40% in the 0.2-0.3 mm grain size sand can be added. 2-3 mm thick, the application is made. The mixture should be used within 1 hour. |
Storage Conditions | Not receive direct sunlight 5-35 ° C increase in environments, can be stored for one year in unopened original packaging. Must be protected from excessive heat and humidity. |
Packaging | I. Component: 19 kg / II. Component: 5.0 kg |

EUROMIX SOLVENT FREE EPOXY PRIMER
Two-component solvent free epoxy resin, a transparent primer.
Solvent-free epoxy
coating applied to the concrete surface before the surface
to feed and will be
applied to the surface of the coating material ensures a strong
adhesion to.
APPLICATION AREAS | Solvent-free epoxy floor coating on concrete surfaces safely used as a primer before. |
COLOUR | Colorless |
Specifications | Density (g / ml) (20 ° C): 1.10 ± 0.05
Brightness: Bright Flash Point (° C): Non-flammable Heat Strength (Dry) (° C): 140 Covering Capacity (Theoretical): 3 - 4.5 m² / kg (150 to 250 μ dry film thickness) Mixing ratio (by weight): I. Component: 14 / II. Component: 6 (Hardener) Mixture Life (20 ° C): 30 40 minutes. |
Drying Time (20 ° C - Max. 85% relative humidity) |
First Movement: 1 - 2 hours to,dry : 5-6 hours recoat: 10 - 12 hours Full Hardening: 7 days |
Thinning rate | Addition of thinners is not recommended: |
Application 1 | Application will be providing concrete surfaces, must be clean and dry. If there is oil on the surface, chemical cleaning materials to be cleaned, been absorbed in large amounts by burning oil should be cleaned if you have. However, the oil fields o perated deep broken to be repaired. |
Application 2 | 1. and II. Attention to the mixing ratio of the components are mixed together, m² 0.250 kg to be used bristle brush or roller with approximately 200μ thick is applied to the cleaned concrete surface. Very porous surfaces should be twice application. |
Storage Conditions | Not receive direct sunlight 5-35 ° C increase in environments, can be stored for one year in unopened original packaging. Must be protected from excessive heat and humidity. |
Important Notices | Components must be mixed with each other During application ambient temperature must be between 5-35 ° C. After each application, application tools should be cleaned with Epoxy Paint Thinner. Discharging sewage and water channels should definitely paint. Application, as noted above and should be done in well-ventilated place |
Packaging | I. Component: 14 kg / II. Component:6.0 kg |
